Contact Us   
Search   
Your Position: Home > News

What UV Curing Can Do For You

2015/11/17      view:


UV curing offers manufacturers many benefits. Below you’ll find additional information on some of the most significant ones. 


http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifInks, coatings, and adhesives with dramatically improved physical properties 

 

The reasons for considering UV usually include a number of improved physical properties such as improved gloss, better scratch and abrasion resistance, better chemical resistance, resistance to "crazing," hardness, elasticity, adhesion, or bond strength. While these technical features can be measured precisely, determining their actual economic value is usually based on superior product performance which may result in increased market share or increased sales. 

 

http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifFaster production speeds and capacity 

 

Any process requiring less space, allowing higher production speeds, involving less direct labor, makes those facilities and resources available for higher production capacity. Less down time and higher throughput increase machine utilization, and have a direct effect on plant capacity. In general, UV curing offers increased productivity and better plant and equipment utilization. 

 

http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifReduction of Work-in-process 

 

This factor has become one of the most powerful cost factors in reduction of manufacturing cycle time. Reducing work-in-process saves significant capital and improves cash flow. 

 

A manufacturer of complex electro-optical devices manufactures a product which, when assembled, carries a value of approximately $50,000, and produces 50 assemblies per month. Ten to fifteen adhesive bonds are required in each of the subassemblies which go into a complete product, and a total of approximately 100. When using both RTV and epoxies for these bonds, each bond or seal required two to three days to set up before it is tested, and sequential assembly is necessary. The total cycle time of the product was four months. 

 

The use of UV curable adhesives reduced the cycle time of a subassembly to 2 hours, and the total product cycle time to 4 days. The work-in-process product value (assuming a straight-line value added rate) of 4 months was:
 
 WORK-IN-PROCESS  
USING 2-PART ADHESIVES: 
$50,000/unit x 50/mo x 4 mo  =  $2,500,000  
     
 2 (G.P. of 50%)x 2 (to average)   
   
USING UV ADHESIVES: 
$50,000/unit x 50/mo x 0.03 mo  =  $18,750  
     
2 (G.P. of 50%)x 2 (to average) 

 

This example was simplified in that one-half of the finished product value (price) was used as an assumed cost, and that the product cost rises steadily from zero to full cost over the product cycle. The significance of the example is the huge amount of capital which can be tied up in work-in-process. 

 

http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifDramatically reduced set-up & clean-up labor 

 

Because UV chemistries won’t cure without exposure to UV energy, they can often be left overnight without fear of the ink or coating “drying” in the machine. This is often an advantage for graphic arts printing presses, plastic decorating machines, marking/coding machines, etc. The example below is for a graphic arts printing press. 

 

Press Set-Up/Clean-Up 

 

The number and types of presses, type and complexity of jobs, run lengths all affect uptime. The reduction of set-up and clean-up required with UV is the most often recognized operating cost benefit associated with UV. 

 
PRESS SET-UP/CLEAN-UP TIME COST  
UV Cured Material: 
1 hr/day @ $500/hr  =  $ 500/day  
   
Solvent or water based material: 
2½ hr/day @ $500/hr  =  $ 1,500/day 

 

http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifLess floor space needed 

 

Typically drying ovens require significantly more floor space than a UV curing process. For example, a drying oven for a conventional web coating line may extend for 50 to 100 feet, a space consumption in the neighborhood of 500 to 1000 square feet. At a floor space cost alone of only $0.50/ft2/month, that costs $3000-6000 per year. The equivalent UV "dryer" would require 50 to 100 square feet. 

 

Another example: a thermal dryer for a one-pass bottle screen printer may be 40 feet long, while an entire 3-color printer with UV cure at each color station is only 13 feet in length. 

 

Some processes require long cure times which can increase the floor space needed. For example, adhesive and potting applications using two-part adhesives or RTV types of compounds must allow cure time, usually measured in days. If the number of parts is large, the consumption of floor space could be significant. Fiberglass composite parts also require significant cure times and because the parts are usually quite large (bathtubs and showers) the floor space needed for part curing can be significant. UV curing significantly reduces the cure time in these examples, thus reducing the floor space requirements. 

 

http://www.sz-jiada.com/AdminBeat/Keditor/themes/common/anchor.gifIncrease yield and reduce scrap 

 

Because UV curing only takes seconds, detection of curing problems can happen immediately, thus reducing scrap. For example, a two-part adhesive might take days to fully cure and then quality control testing can be done. During this time production continues, possibly resulting in scrap parts. 

 

In painting and coating applications, the reduced time it takes to UV cure eliminates the chance for dust and particles to contaminate the part surface during painting – another common cause for scrapped parts. In some UV processes, quality control procedures call for inspection of the ink, coating or adhesive application prior to UV curing. If any problems are found, the ink, coating or adhesive can be easily removed, the problem solved, and the part put back on the production line.